Turned Timber Verandah Posts — V1 to V8

Which verandah post designs are available?

V1 to V8. V1 through V5 are the five standard turned profiles, with a squared base and capital and a turned shaft between them, and V3 is also made as V3B. V6 is a lighter, plainer post and is the one to ask about if you want it chamfered or fluted rather than turned; it comes as V6, V6B and V6H. V7 is made plain, fluted (V7F), or fluted with a handrail block (V7FH) — that block is what a balustrade rail fixes into, so specify it at order time rather than cutting one in later. V8 is the heaviest design in the range. The range includes Federation and Victorian verandah post designs, and the eight designs are photographed square-on if you are settling the design before the size.

What sizes and lengths do they come in?

Squared sections are 88 x 88mm, 112 x 112mm and 135 x 135mm. Standard lengths are 2.4m, 2.7m, 3.0m, 3.3m and 3.6m — five steps of 300mm. Confirm the required overall length and structural specification with your builder before ordering. The three sections apply across V1 to V6; V7 and V8 are made in 88 x 88mm and 112 x 112mm only, so if you need a 135mm post choose from V1 to V6. Posts can also be custom made to suit the size and style of the house if none of the eight suits.

What are the posts made from?

Every one of our verandah posts is made from LOSP H3 treated pine in Australia. The range includes turned and chamfered profiles. The H3 hazard rating covers exterior timber used above ground, protecting the post against fungal decay and insect attack — which is what takes out the base of an old verandah post first, at the point where it meets the deck and stays wet. As external LOSP H3 treated pine used above ground, our posts carry our 25 year guarantee. Prime all six faces, including both end grains, with two thin coats of oil-based primer before the post goes up, then topcoat. Priming before installation helps protect the faces and end grain that become inaccessible once the post is fixed.

How do I match a post that is already there?

The most accurate method is to send us the original. Prop and support the verandah roof properly first, ease the post out so the profile stays intact, and drop it in to the Bayswater workshop or freight it — never remove a load-bearing post before the structure is supported, and get a builder in if you are unsure. If the post cannot come out, photograph it instead: one full-length shot with a tape measure laid flat alongside it, then close-ups of the capital, every turned section, any chamfer or moulding, and the base or plinth, all taken square-on in daylight. Add the floor-to-beam height. Clear photographs and measurements help the workshop assess the profile; send the original piece where practical for the most accurate comparison. Ask about our timber-profile matching service. Call 03 9720 1996.

What else goes with a verandah post?

Verandah rafters, post caps and post tops, pyramid caps, capitols and fence post caps all finish the post itself. Corner brackets fill the angle at the head of the post, and fretwork or a frieze panel fills the bay between one post and the next.

Choosing a replacement verandah post before you order

Match the squared section, overall length and position of the turning separately. A similar silhouette alone does not show whether the base, capital and handrail fixing points line up with the existing verandah. Include those details in your enquiry, and mark which measurements come from a surviving post and which come from the opening. Have your builder confirm the required structural specification before selecting a decorative profile.

For a repair, send a full-length photograph and close-ups of the surviving details. If the bottom has decayed, say so rather than treating the remaining length as the original length. The guide to matching a damaged verandah post explains what to photograph before requesting a replacement. Compare the V-code, section and length together on the pricing page; ask for confirmation where the combination is not listed. Add your quantity and delivery postcode so the enquiry covers the complete order.

Find prices for your verandah post design

Each price sheet identifies the design, squared section and overall length. Prices are per post; check any separate caps, capitals or droppers your order needs. Choose the V-code that matches the profile:

• V1 verandah post prices
• V2 verandah post prices
• V3 verandah post prices
• V4 verandah post prices
• V5 verandah post prices
• V6 verandah post prices
• V7 verandah post prices
• V8 verandah post prices

Request a verandah post quote with the V-code, section, overall length, quantity and delivery postcode. For a profile outside the catalogue, send a sample or photographs through our timber matching service.

Related pages

• Shaped rafters — bullnose, convex, concave, Olde Gothic
• Ball, Acorn and Windsor post knobs, and pyramid tops
• Every CB and EB bracket code, with its size
• Fretwork and frieze panels, internal and external
• Assembled balustrade panels, base rails and handrails
• The eight post turnings, seen close up

Related workshop guides

• How to Match a Damaged Verandah Post Without Replacing the Whole Row
• A Practical Decorative Timber Checklist for Verandah Restoration